What is Canon Pixma Error Codes 6B10, 9000,5C20

Paper feed cam sensor error or Error Code 6B10
 
Condition: An error occurred in the paper feed cam sensor during paper feeding from the cassette, or the paper absorbing a large amount of ink jammed in the PF rear guide.
 
Solutions:

• Jammed paper in the PF rear guide (when a large amount of ink was absorbed in the paper);
• - remove the jammed paper and foreign material.
• check for foreign material or paper debris in the cassette or in the PF rear guide;
• - remove foreign material.
• If other solution fail, replace one off the following part
• - PF pick-up unit
• - Logic board

USB Host VBUS overcurrent or Error Code 9000
 
Condition:

The USB Host VBUS is overloaded.
 
Solutions:

• Replace Logic board

Pump roller sensor error or Error Code 5C20
 
Condition:

The pump roller position cannot be detected.
 
Solutions:

• Replace Purge drive system unit

Read More...

Call Us +1-855-517-2433 (Toll Free)

How to Reset Error Code E08 in Canon MP287 - Absorber Full

When the MP287 is turned on, it will immediately appear on the LCD panel error E08 MP287. And when we do print command, then the monitor screen will show “The Ink Absorber is Almost Full”. Caption MP287 E08 error on the screen as follows:

1. Turn on the Canon MP287, MP287 LCD then the panel will pop up error E08, and there is a description of “The Ink Absorber is Almost Full” on the screen of your monitor.
2. Download Resetter MP287 at this link
3. Canon MP287 printer must be in a state of SERVICE MODE. Do I read the next step.
4. Canon MP287 Turn off the E08 error by pressing the power. Do not unplug the power cord.
5. Press and Hold the button STOP / RESET followed by pressing the POWER button. So both buttons depressed position.
6. Release the button STOP / RESET but do not release the button POWER.
7. In these circumstances the POWER button is still depressed, press the STOP / RESET 6 times.
8. Then release both buttons simultaneously. Then the Canon MP287 will be in Service Mode condition.
9. LCD Panel MP287 will blank / dark and in your computer will detect new hardware. Ignore it.
10. The next step Exctract and Run Service Tool for MP287 MP287 E08 error you downloaded earlier.
11. Click the “PLAY”, then the printer will proceed, then MP258 will print one page with the words “D = 000.0″
12. Click “Clear EEPROM”.

13. Then click “EEPROM”, and the printer will print the results MP258 Resetter. Writing one line as follows: “TPage (COPY TTL = 00 000 = 00 000)”.
14. Canon MP287 Turn off by pressing the power.
15. Canon MP287 printer that error E08 will be normal again.

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

Printer Canon Pixma MP258 – Absorber Full

Printer Canon Pixma MP258 – Absorber Full

If your printer show P07 error it means that your ink absorber inside the printer is almost full. In order to solve this you need to clear or reset the counter protection of your printer. To do this, follow this steps.

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter at the bottom of this post.

FIRST STEPS:  Entering Service Mode

You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.

2. Hold down STOP/RESET button and press Power button.

3. Keep holding down Power button and let STOP/RESET button go.

4. Then Press STOP/RESET button twice then let BOTH buttons go.

5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click "servicetool.exe"

2. Load some papers in your printer and press the "Main" Button once, wait until the printing is done.

3. Then press "EEPROM Clear" button to clear EEPROM.

4. Then press EEPROM button and the printer will print some text.

5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

How to Clear a Paper Jam on a Canon Inkjet Printer

How to Clear a Paper Jam on a Canon Inkjet Printer

For many people, maintaining a Canon Inkjet Printer in the home or office can be expensive and frustrating. There are numerous error messages and they always come at inconvenient times. Many Canon printers today have LCD monitors to help us understand problems that arise, however, many inkjet printers do not come with such monitors. Most of us do not read the Canon Inkjet Printer manuals thoroughly and have little to no idea what the blinking error light means. Paper jams are among the most common problem with Canon Inkjet Printers. Follow these instructions to learn how to clear a paper jam on a Canon Inkjet Printer:

Instructions

Protect yourself from shock. Disconnect the power cord from the back of the Canon Inkjet Printer. This is an important step when working inside ANY electronic device.

Unhinge the back access panel of the printer. It seems repetitive to say this, but this door will be in the BACK of the printer.

Look through the opened back panel and look for paper. Remove any and all paper you find jammed there.

Close the back access panel. Make sure that it latches into place and looks the same way that it did before you opened it.

Find the front or top access panel. This is the panel you would lift to change ink cartridges. Open this access panel. If the carriage that holds the ink cartridges moves, then you forgot to unplug the printer, go back and do that now. Look for paper that may be jammed in this area of the printer.

Remove any paper you find jammed here. When pulling from the front there will be resistance from the paper feeder. Pull slowly or the paper will rip and create a more stressful problem.

Close the front access panel. Make sure that it falls or latches back in place. It should look the same way that it did before you opened it.

Plug the printer's power cord into the wall outlet, and attempt to print again. If the printer prints the job, then you have successfully removed the paper jam.

Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)

 

Canon Printer Paper Won't Feed

Reason

Paper feeding problems with Canon printers can be related to the media (paper) condition, paper quality or the printer. Paper not feeding properly can be accompanied by paper jams, too. Printer and paper preparation can go a long way to alleviate these kinds of issues. Follow some steps to ensure your paper feeds correctly in your Canon printer.

Solution

1 Remove any jammed paper from the Canon printer. Pull the paper out from the sheet feeder in the direction that the paper was traveling. This will help avoid damage to the rollers and associated plastic parts. Allow the printer to reset itself afterward.

2 Lift any covers and lids, and wipe the rollers with a soft, damp cloth. A light colored cloth will help you identify dirt that comes off the rollers. Clean the rollers gently with the cloth. Clean the rollers until no more dirt appears on the cloth. Allow the rollers to dry.

3 Fan and then load fresh paper in the Canon printer. Use dry, flat paper. Don't overfill the tray. Discard any paper that curls or is wrinkled. Load the paper so that the left edge rests against the paper guide. Set the paper guide so that it fits the paper. You will see embossed markings on the paper tray that represent the size of the paper you are using. For example, move the paper guide to the "Letter" position if you are using letter-sized paper. Check that the paper is stacked perpendicular to the tray. Everything should be square
Read More...

Any Kind of Canon Printer Problems Call Us
+1-855-517-2433 (Toll Free)